Special tools for cars

for scraper No. 12749.

Used to remove adhesive residue and stickers from the windshield. It can also be used as a metal scraper and seal.

from inner 1/2 "to outer 3/8".
Maximum torque 202 Nm, DIN 3123 / ISO 3316,
High quality HPQ® steel.

10 pcs

used to remove adhesive residue and stickers from the windshield, with a replaceable 0.3 mm wide blade; in a protective case.

ze speciální oceli; na odtsraňování zbytků těsnení, např. tesnění hlavy valců.

Used to pull or push a cutting wire through hardened glue.

is used to thread the cutting wire through the hardened glue; it is a steel tube with a diameter of 2.5 mm, with a brass handle

is used to tension and fix freshly glued windscreens; plastic fabric.

Cross section 0.6 x 0.6 mm, made of stainless steel. The removed piece of cutting wire does not loosen the firm cohesion of the rest of the wire on the spool.

is used to fix and counter hold the cutting wire in the vehicle interior. For the long handle versus the holder, it is especially suitable for deep-lying windscreens.

is used to fix and counter hold the cutting wire in the vehicle interior.

for screws with internal wedge slot (Ribe CV®), 9-piece, Contents: M5; M6; M7; M8; M9; M10; M12; M13; M14

is used to pull the cutting wire through the glued seal.

3/8 "square drive, extra long, with rubber insert, for deep-laid, hard-to-reach, spark plugs with M12 x 1.25 mm thread. For cars
Citroën: with C5 2 engine, 0 l HPI;
Peugeot: with 406 HPI engine;
Renault: Twingo, Clio, Kangoo with 1.2 l engine, 16V.

120 mm diameter surface, with suction mechanism and safety lock, made of excellent quality plastic; acid-resistant and oil-resistant. There are holes for the strap in the handle. Load capacity 30 kg.

clamping hole 3/8 ".

a pair of suction surfaces with a diameter of 120 mm, with a suction mechanism and a safety lock, made of plastic of excellent quality; acid-resistant and oil-resistant. There are holes for the strap in the handle. Load capacity 60 kg.

as No. 10350N, but without a double vacuum suction cup for lifting glass.

1 pc. tensioning handle 1 pc. against holder 1 pc. spool of special cutting wire (50 m) 2 pcs. double vacuum suction cup for lifting glass.

With the axial, self-tapping threaded tip, it is possible to drill welding points cleanly and without burrs. It does not slip out of the spot weld, which can be post-machined.

5-piece for flat plug housings.
Contents:
No. 1551, 1552: cable unlocking for plugs with two unlocking channels, contacts 2.8 and 5.8 mm
No. 1553, 1554, 1555: cable unlocking for plug with one unlocking channel 2.8; 5.8 mm
Content:
No 1551, 1552: Entry tool for H & # 252; lsen with two increments
2.8 and 5.8 mm in plug with double channel < br /> No 1553, 1554, 1555: Input tools for & # 223; r
Contact & # 223; e 2.8 and 5.8 mm in plugs with an input channel

With the axial, self-tapping threaded tip, it is possible to drill welding points cleanly and without burrs. It does not slip out of the spot weld, which can be post-machined.

HSSE steel, used for milling welding points in bodywork and sheet metal machining; with replaceable cutters with a diameter of 10 mm; usable in both directions. The milling depth is adjustable with a screw. It does not deform or damage the sheets.

with gear mechanism, built-in spring opens automatically. Great cutting power. Also for 1.8 mm wide sheets. Can also be used on stainless steel sheets up to 1.2 mm wide.

with gear mechanism, built-in spring opens automatically. Great cutting power. Also for 1.8 mm wide sheets. Can also be used on stainless steel sheets up to 1.2 mm wide.

with gear mechanism, built-in spring opens automatically. Great cutting power. Also for 1.8 mm wide sheets. Can also be used on stainless steel sheets up to 1.2 mm wide.

with gear mechanism, built-in spring opens automatically. Great cutting power. Also for 1.8 mm wide sheets. Can also be used on stainless steel sheets up to 1.2 mm wide.